PocketLearn Unofficial study aid

CDL Pre-Trip Inspection Practice Questions

Vehicle walkaround, inspection checks and recognizing unsafe conditions. Practice with 40 original questions and rationales.

Start the free practice test

All 40 questions with answers

Try each question first, then open the answer. To practice them as a timed quiz with a score and a mistake list, use the practice test.

1. The previous driver’s required inspection report lists a safety defect. What should the next driver verify before departure?

Show answer

Answer: A. Review the report and confirm the required repair certification.

The driver must be satisfied the vehicle is safe. When a report is required, review it and acknowledge required repair certification as applicable.

2. Dispatch tells a driver to leave before the walk-around because the truck was serviced yesterday. What is the driver’s responsibility?

Show answer

Answer: B. Be satisfied the vehicle is in safe operating condition before driving.

Recent maintenance does not replace the driver’s obligation to be satisfied that the vehicle is safe before driving.

3. At a vehicle inspection skills test, a candidate silently points to the steering linkage. What is missing?

Show answer

Answer: C. Identify the component and explain the condition being checked.

The California modernization checklist requires identifying and explaining the relevant check, as well as pointing or touching where applicable.

4. During a trip a driver smells hot rubber after a normal stop. How should this affect the next action?

Show answer

Answer: C. Stop in a safe place and investigate the source.

Smell can be an early sign of an equipment problem. Investigate safely before continuing.

5. A driver switches from a straight truck to a tractor-trailer for a skills test. Which preparation is appropriate?

Show answer

Answer: D. Use the current state checklist for the actual configuration.

The state checklist distinguishes vehicle configurations, including combination vehicle equipment.

6. Before opening a cooling system cap, the driver sees the engine is hot. How should coolant level be checked?

Show answer

Answer: A. Use the visible reservoir marking without opening the hot system.

Use the designated level indicator and avoid opening a hot pressurized cooling system.

7. A fresh oily puddle is visible below the engine area. What should the driver do before leaving?

Show answer

Answer: B. Trace the likely source and resolve an unsafe leak.

A fresh puddle calls for checking where the fluid came from and whether safe operation is affected.

8. A steering hose rubs against a bracket and the outer cover is worn through. What does the finding indicate?

Show answer

Answer: A. The hose and routing need attention before safe operation.

Abrasion and damaged routing can lead to a leak or loss of steering assistance.

9. During the engine-area check, a steering linkage fastener is visibly missing. What should the driver conclude?

Show answer

Answer: C. The steering connection may be insecure and needs correction.

Loose or missing steering hardware can compromise control. Fluid level does not restore a mechanical connection.

10. At startup a warning lamp remains lit beyond its normal self-test. What is the best next action?

Show answer

Answer: A. Identify the warning and determine whether departure is safe.

Distinguish normal lamp checks from a warning that remains active and address the underlying issue.

11. A wiper blade moves but leaves a broad streak across the driver’s sight line. What should be checked?

Show answer

Answer: C. Blade condition and washer operation in the affected area.

Wipers and washers must provide effective forward visibility, including in the driver’s primary sight line.

12. The cab seat belt latches but the webbing is torn. What is the appropriate finding?

Show answer

Answer: B. The belt is defective despite the working latch.

A functioning latch does not compensate for damaged restraint webbing.

13. During inspection the driver finds the fire extinguisher gauge in the acceptable range but the unit loose in the cab. What is needed?

Show answer

Answer: C. Secure the extinguisher in its designated mount.

An extinguisher must be accessible and secured, in addition to being serviceable.

14. Which check best verifies that the cab heater can restore a fogged windshield?

Show answer

Answer: C. Operate the defroster and check airflow at the windshield.

Direct airflow at the windshield verifies the function needed for defogging.

15. A tire looks properly inflated at a glance. How should the driver verify pressure?

Show answer

Answer: A. Use an appropriate tire pressure gauge.

Visual appearance and sound are poor substitutes for a gauge reading.

16. A steer tire has 3/32 inch tread in a major groove. What should the driver conclude under the cited handbook?

Show answer

Answer: D. It falls below the front-tire minimum.

The cited commercial handbook specifies at least 4/32 inch in major grooves on front tires.

17. A dual tire pair has enough tread but the sidewalls touch. What is the concern?

Show answer

Answer: C. The contact is a defect that requires correction.

Dual tires should not contact each other or other vehicle parts during operation.

18. A driver finds a sidewall cut with reinforcing material visible. What should happen?

Show answer

Answer: B. Treat the tire as unsafe and arrange correction.

Visible reinforcement indicates significant tire damage even if it currently holds pressure.

19. Rust trails radiate from several wheel fasteners. Which follow-up is most relevant?

Show answer

Answer: A. Inspect for loose fasteners or wheel movement.

Rust trails can signal fastener movement and warrant closer inspection.

20. Fresh oil is visible on the inside of a wheel near the hub. What should the driver check?

Show answer

Answer: B. The hub seal and whether lubricant reached braking surfaces.

Hub leakage can threaten lubrication and contaminate brake friction surfaces.

21. One leaf spring is shifted sideways from the stack. What is the appropriate finding?

Show answer

Answer: A. The spring assembly or its retention may be defective.

Shifted leaves or loose spring hardware can compromise axle location and suspension integrity.

22. One air suspension corner sits low and a hiss comes from its airbag. What is the relevant defect?

Show answer

Answer: D. A suspension air leak may affect ride height and stability.

A leaking airbag can prevent the suspension from supporting the vehicle as designed.

23. The dash turn indicator flashes normally. How should the exterior signal be verified?

Show answer

Answer: D. Observe the corresponding exterior lamps in operation.

An in-cab indicator is not proof that all corresponding exterior lamps are functioning.

24. A rear stop lamp illuminates, but its lens is broken and produces the wrong color. What is the inspection finding?

Show answer

Answer: D. The lens defect requires correction even though the lamp lights.

The inspection covers proper lens condition and color as well as illumination.

25. A clean trailer marker lamp has no output. What should the driver do?

Show answer

Answer: B. Verify the circuit and correct the inoperative lamp.

Check each required light. A reflector or another lamp does not restore the inoperative marker.

26. A side mirror shows a clear image but its mount moves when lightly checked. What matters for safe travel?

Show answer

Answer: B. Correct the loose mount so the mirror holds its position.

A loose mirror can shift in motion and remove the required view.

27. During the walk-around, mud covers the rear reflectors. What is the best correction?

Show answer

Answer: B. Clean them and verify they are intact and securely attached.

A covered reflector cannot provide the expected visibility. Verify condition and mounting after cleaning.

28. An air line is rubbing on a moving suspension part. What should the driver inspect for?

Show answer

Answer: A. Damage, leakage, and inadequate clearance at the contact point.

Brake hoses require sound routing without abrasion or interference from moving parts.

29. A parking-brake hold test shows the vehicle moving against the applied brake. What should the driver do?

Show answer

Answer: D. Treat the brake as faulty and have it corrected.

The applied parking brake must hold during its proper test. Movement indicates a fault.

30. During a low-speed service brake test, the truck consistently pulls left. What does the finding indicate?

Show answer

Answer: D. Uneven braking or another control fault needs investigation.

Pulling under service braking is a warning of a possible brake or steering problem.

31. The low air pressure warning fails during the prescribed test. What is the departure decision?

Show answer

Answer: C. Do not operate until the warning fault is corrected.

The driver must be alerted to low system pressure. A working gauge does not substitute for a failed warning system.

32. During the prescribed applied leakage test, pressure falls faster than allowed for the vehicle. What should the driver do?

Show answer

Answer: D. Keep the vehicle out of service until the leak is addressed.

Excessive pressure loss means the system may not maintain adequate braking air.

33. A wheel-area inspection finds friction surfaces contaminated with lubricant. What is the appropriate finding?

Show answer

Answer: D. Braking performance can be compromised and needs correction.

Lubricant can reduce friction and make braking uneven or ineffective.

34. The trailer apron does not sit flush on the fifth wheel after coupling. What should the driver do?

Show answer

Answer: B. Stop and verify a correct coupling before travel.

A gap may signal incorrect engagement. Inspect the coupling and correct it before driving.

35. A tug test feels firm, but visual inspection shows the fifth-wheel jaws have not closed around the kingpin shank. What is the decision?

Show answer

Answer: C. Do not proceed until visual and functional checks agree.

A tug check alone does not verify that the jaws properly enclose the kingpin shank.

36. After coupling, the driver finds the fifth-wheel release handle out of its locked position. What should happen?

Show answer

Answer: A. Verify the mechanism is fully engaged and secured.

The release mechanism and safety latch must be in their proper locked positions.

37. A trailer air connection seal is damaged and leaks after hookup. What is the appropriate action?

Show answer

Answer: C. Correct the leak and verify the connections before travel.

Air lines and seals must maintain a secure, leak-free connection to support trailer braking.

38. Trailer landing gear is raised but the crank is hanging unsecured. What should the driver do?

Show answer

Answer: A. Secure the crank in its intended retainer.

The landing gear and crank should be secured to prevent movement and interference during travel.

39. During a tight turn the electrical cord would pull taut between tractor and trailer. What should the driver correct?

Show answer

Answer: D. Route it with sufficient supported slack for turns.

Connections need clearance and supported slack for articulation without stretching or dragging.

40. The sliding fifth-wheel locking pins are not fully engaged. What is the departure decision?

Show answer

Answer: B. Confirm full pin engagement before moving onto the road.

The slider must be mechanically locked in its intended position before travel.

Practice all 40 questions

Frequently asked questions

Is this an official exam?

No. These are original, unofficial practice questions written by PocketLearn. They are not released exam items. For exam preparation. Check the current official exam materials and rules for your test.

How many questions are there?

40 multiple-choice questions. Each question has an explanation.

Is it free?

Yes. You can open the practice set without an account; signing in lets you save progress and review mistakes.

Can I use it on my phone?

It opens in a mobile browser. A laptop or tablet is easier for longer sets.

More free practice tests