PocketLearn Unofficial study aid

CDL Air Brakes Practice — Set 3

Practice selected New York manual air-brake topics through original scenarios. 49 CFR 383.111(b) is used for scope mapping, not equipment thresholds. Unofficial study material. 个人学习整理,以官方手册为准

Start the free practice test

All 40 questions with answers

Try each question first, then open the answer. To practice them as a timed quiz with a score and a mistake list, use the practice test.

1. A fleet replaces an engine-driven compressor. Which connection should the technician expect to find on the old unit?

Show answer

Answer: C. An engine gear drive or V-belt

The engine supplies compressor power through gears or a belt; wheel rotation is not the drive source. Source: New York CDL Manual §5.1.1.

2. Before dispatch, a driver finds that the compressor has a separate oil reservoir. Which check belongs on the pre-trip list?

Show answer

Answer: D. Check the compressor oil level

A compressor with its own lubricant supply needs an oil-level check before driving. Source: New York CDL Manual §5.1.1.

3. A cold-weather truck has an alcohol evaporator. Which problem is this device intended to reduce?

Show answer

Answer: B. Ice forming inside air valves

Alcohol in the air system helps prevent internal ice that could interfere with valve operation. Source: New York CDL Manual §5.1.5.

4. At a subfreezing morning inspection, the evaporator container is nearly empty. What is the appropriate routine action?

Show answer

Answer: C. Check and replenish its alcohol supply

The manual calls for checking the container daily in cold weather and filling it as needed. Source: New York CDL Manual §5.1.5.

5. A mechanic is locating the air-system safety relief valve. Which tank should be examined first?

Show answer

Answer: A. The first tank fed by the compressor

The relief valve is fitted to the first reservoir receiving compressor output to protect against excess pressure. Source: New York CDL Manual §5.1.6.

6. A shop simulation raises reservoir pressure toward 150 psi. Which device normally provides overpressure relief near this level?

Show answer

Answer: C. The tank safety relief valve

About 150 psi is the usual safety-valve opening setting, not a normal pressure target for driving. Source: New York CDL Manual §5.1.6.

7. During a yard inspection, air escapes through the safety relief valve. How should the driver treat that finding?

Show answer

Answer: A. Arrange mechanical correction of the fault

Relief discharge indicates a fault requiring repair; the relief valve is a protective device rather than a routine operating control. Source: New York CDL Manual §5.1.6.

8. A trainee sees an S-cam rotating as a brake chamber pushrod extends. What should happen at the shoes?

Show answer

Answer: D. They spread against the drum interior

Cam rotation spreads the shoes so their linings contact the inside of the drum and produce braking friction. Source: New York CDL Manual §5.1.8.

9. On a training stand, an S-cam returns after the pedal is released. What pulls the shoes clear of the drum?

Show answer

Answer: B. The brake shoe return spring

The shoe return spring withdraws the shoes as the cam returns, allowing free wheel rotation. Source: New York CDL Manual §5.1.8.

10. A technician demonstrates a wedge brake on a cutaway model. Which movement applies its shoes?

Show answer

Answer: D. A wedge moves between the shoe ends

In a wedge design, the chamber pushrod drives a wedge between shoe ends and forces the shoes apart. Source: New York CDL Manual §5.1.8.

11. An air-disc brake cutaway shows a power screw turning. Which action produces braking friction?

Show answer

Answer: D. Pads clamp the rotating disc faces

The power screw causes the caliper pads to grip the rotor rather than expanding drum-brake shoes. Source: New York CDL Manual §5.1.8.

12. A truck's brake lamps illuminate during an air-brake application. What normally triggers their electrical switch?

Show answer

Answer: B. Air pressure from brake application

The stop-light switch responds to air pressure and closes the electrical circuit for the brake lamps. Source: New York CDL Manual §5.1.12.

13. An older truck has a manual front-brake selector marked normal and slippery. Which setting preserves normal stopping power?

Show answer

Answer: A. Keep the selector at normal

The slippery setting reduces front braking pressure and stopping power; the manual directs use of normal. Source: New York CDL Manual §5.1.13.

14. A parked truck uses spring brakes and gradually loses stored air overnight. What supplies the applied holding force?

Show answer

Answer: C. Mechanical force from powerful springs

Spring brakes hold mechanically; stored air can leak away and is used to hold the springs back during driving. Source: New York CDL Manual §5.1.14.

15. At a dry, level parking space with cool brakes, a driver uses the newer yellow diamond-shaped control. Which action applies the parking brakes?

Show answer

Answer: D. Pull the control knob outward

Pulling the yellow push-pull control applies the spring parking brakes; pushing it inward releases them. Source: New York CDL Manual §5.1.15.

16. A trainee plans to press the service pedal hard while the spring brakes are already applied. What concern should the trainer explain?

Show answer

Answer: A. Combined forces can damage brake parts

Service air pressure can add to spring force and damage components. Some systems prevent compounding, but the manual warns against relying on that protection. Source: New York CDL Manual §5.1.15.

17. A bus has a modulating spring-brake lever. During a service-brake failure, what does moving this lever farther accomplish?

Show answer

Answer: B. It applies the spring brakes more firmly

A modulating valve provides graduated spring-brake application for controlled use during a service-brake failure. Source: New York CDL Manual §5.1.15.

18. A driver parks a vehicle equipped with a modulating spring-brake lever. How should that lever be secured?

Show answer

Answer: C. Move it fully and engage its locking device

For parking, the modulating lever must be moved fully and retained by its locking device. Source: New York CDL Manual §5.1.15.

19. A disabled bus has a separate emergency spring-brake release tank. Why should the driver plan the move before using it?

Show answer

Answer: A. Its stored air permits only a few releases

The separate release reservoir has limited capacity; repeated releases can exhaust it before the bus reaches a safe position. Source: New York CDL Manual §5.1.15.

20. On a bus with the spring-loaded emergency release button, the driver lets go of that button. What should happen?

Show answer

Answer: D. The spring brakes apply again

Holding the special button uses separate reservoir air to release the springs; releasing the button reapplies them. Source: New York CDL Manual §5.1.15.

21. A driver opens the engine compartment of a belt-driven compressor truck. Which belt condition is relevant to brake readiness?

Show answer

Answer: A. Sound material and proper tightness

The engine-compartment inspection includes the condition and tightness of the compressor drive belt. Source: New York CDL Manual §5.3.1.

22. At a walk-around, a driver sees a drum crack extending across about three quarters of its friction-area width. What is the proper finding?

Show answer

Answer: A. A drum defect needing repair

A crack longer than half the friction-area width exceeds the manual's stated condition for drums or discs. Source: New York CDL Manual §5.3.2.

23. A wheel inspection reveals grease-soaked friction linings of otherwise substantial thickness. How should the driver classify them?

Show answer

Answer: D. Contaminated friction material requiring repair

Linings must be secure and free of oil or grease contamination; remaining thickness does not make contaminated linings acceptable. Source: New York CDL Manual §5.3.2.

24. With a vehicle secured on level ground for an S-cam slack-adjuster hand check, why are the parking brakes released?

Show answer

Answer: C. To permit adjuster movement during checking

The manual's secured hand-check setup releases the parking brakes so adjuster movement can be assessed. Source: New York CDL Manual §5.3.2.

25. During a secured straight-truck inspection, the low-air warning has already activated. Continued fanning makes the parking knob pop out at the manufacturer's specified low pressure. What does that indicate?

Show answer

Answer: D. Automatic spring-brake application is occurring

As pressure falls into the specified range, the parking valve closes and the spring brakes apply automatically. This is a stationary test, not a driving strategy. Source: New York CDL Manual §5.3.3.

26. A manual-transmission truck is making a routine stop for a loading gate. When should the driver depress the clutch?

Show answer

Answer: A. When engine speed approaches idle

For a normal stop, retain the transmission connection until engine speed is near idle, then depress the clutch. Source: New York CDL Manual §5.4.1.

27. A driver has brought a manual-transmission truck to a complete normal stop. Which transmission action prepares for the next move?

Show answer

Answer: C. Select a suitable starting gear

After stopping, the manual directs selecting a starting gear appropriate for moving off. Source: New York CDL Manual §5.4.1.

28. A driver uses controlled braking in a truck without ABS as a car enters the lane ahead. Which pedal strategy fits this method?

Show answer

Answer: B. Use strong pressure short of wheel lock

Controlled braking seeks maximum usable braking while avoiding locked wheels, so steering control remains available. Source: New York CDL Manual §5.4.3.

29. During controlled braking in a truck without ABS, a larger steering correction becomes necessary. What should the driver do with the brakes?

Show answer

Answer: D. Release braking and then promptly reapply

The manual directs releasing during a larger steering adjustment or wheel lock and reapplying promptly when possible. Source: New York CDL Manual §5.4.3.

30. A truck without ABS is using stab braking. The wheels lock during the full application. What is the next action?

Show answer

Answer: C. Release the service brakes

Stab braking alternates full applications with releases at wheel lock, allowing the tires to resume rolling. Source: New York CDL Manual §5.4.3.

31. After releasing locked wheels during stab braking, a driver is ready for another full application. What must happen first?

Show answer

Answer: B. The wheels must resume rolling

Reapplying before the wheels roll prevents the vehicle from straightening; wheel recovery can take up to a second. Source: New York CDL Manual §5.4.3.

32. On a training run, the driver has already recognized a hazard and pressed the pedal, but braking has not yet begun while air travels through the lines. Which interval is being observed?

Show answer

Answer: D. The air-brake lag interval

Brake lag occurs after pedal application and before the air-operated brakes begin acting; it is separate from human reaction time. Source: New York CDL Manual §5.4.4.

33. An instructor asks a trainee to budget for air travel time after pressing the brake pedal. Which minimum planning description matches the manual?

Show answer

Answer: B. About half a second or longer

The manual describes the pneumatic delay as roughly half a second or more; it should not be treated as instantaneous response. Source: New York CDL Manual §5.4.4.

34. A worksheet totals perception, reaction, and friction-braking distances for an air-braked truck. Which additional distance belongs in the total?

Show answer

Answer: B. Distance traveled during brake lag

Total stopping distance includes travel during the pneumatic delay in addition to perception, reaction, and actual braking distances. Source: New York CDL Manual §5.4.4.

35. A simulator separately measures 100 feet of perception travel, 50 feet of reaction travel, 30 feet of brake-lag travel, and 200 feet of braking travel. What is the total?

Show answer

Answer: A. 380 feet of stopping travel

Add all four simulated distances: 100 + 50 + 30 + 200 = 380 feet. These are exercise measurements, not handbook stopping-distance guarantees. Source: New York CDL Manual §5.4.4.

36. Repeated close-spaced stops overheat a delivery truck's drums. What physical change makes shoe contact harder to achieve?

Show answer

Answer: C. Hot drums expand away from the shoes

Thermal drum expansion requires greater shoe travel to make contact and contributes to reduced braking effectiveness. Source: New York CDL Manual §5.4.5.

37. After repeated heavy stops, a technician explains that brake-lining chemistry has changed from heat. What braking effect is expected?

Show answer

Answer: B. Reduced friction at the lining surface

Excessive heat changes lining properties and reduces friction; continued overuse can progress from fade to failure. Source: New York CDL Manual §5.4.5.

38. One brake contributes little because of poor adjustment during repeated city stops. Why can the other brakes become overheated?

Show answer

Answer: A. They must carry more of the stopping work

When one brake stops doing its share, others take extra load and can overheat and fade. Source: New York CDL Manual §5.4.5.

39. After routine parking on dry ground with cool brakes, a driver proposes relying on the selected gear to hold the truck. Which plan follows the manual?

Show answer

Answer: C. Apply the parking brakes before leaving

Parking normally requires the parking brakes. A selected gear is not the parking procedure specified in the manual. Source: New York CDL Manual §5.4.8.

40. A driver leaves a trailer detached overnight at a yard. What precaution does the manual specifically call for?

Show answer

Answer: B. Chock the wheels of the detached trailer

The manual directs chocking a trailer when parked away from the tractor, rather than trusting air pressure to remain available. Source: New York CDL Manual §5.4.8.

Practice all 40 questions

Frequently asked questions

Is this an official exam?

No. These are original, unofficial practice questions written by PocketLearn. They are not released exam items. Unofficial original practice. Check current official exam materials. Not a complete exam review.

How many questions are there?

40 multiple-choice questions. Each question has an explanation.

Is it free?

Yes. You can open the practice set without an account; signing in lets you save progress and review mistakes.

Can I use it on my phone?

It opens in a mobile browser. A laptop or tablet is easier for longer sets.

More free practice tests