CDL Combination Vehicles Practice Set 2 (Unofficial)
Practice combination-vehicle judgment with original single-choice scenarios drawn from New York CDL Manual Section 6. This is Set 2 (CV41–CV80) and does not repeat Set 1 stems. Unofficial practice only — not official, AAMVA, FMCSA, or state DMV examination items.
- Questions: 40 multiple choice, each with an explanation.
- Based on: Facts paraphrased from the New York State Commercial Driver’s Manual CDL-10 (11/25), Section 6 Combination Vehicles, https://dmv.ny.gov/brochure/cdl10sec06.pdf. PocketLearn original scenarios; the manual’s end-of-subsection Test Your Knowledge items were not copied as stems. No eCFR stems in this set.
- Affiliation: Unofficial. Not affiliated with any exam board, agency or state.
- Last reviewed: 2026-11-13.
All 40 questions with answers
Try each question first, then open the answer. To practice them as a timed quiz with a score and a mistake list, use the practice test.
1. A loader has stacked freight high along one side wall of a semitrailer that will run cloverleaf ramps. How should that cargo be arranged to reduce rollover risk?
Show answer
Answer: D. Keep cargo as low as possible, centered on the rig, and evenly distributed
The New York CDL Manual says two things help prevent rollover: keep the cargo as close to the ground as possible, and drive slowly around turns. Keeping cargo low is even more important in combination vehicles than in straight trucks, and the load should be centered and spread out. A load that makes a trailer lean makes a rollover more likely.
2. For this question, use the rollover teaching statement in the selected NY CDL Manual Section 6.1.1, rather than a universal risk estimate for all roads and loads. A fully loaded tractor-semitrailer approaches a tight off-ramp. Which advice and loaded-versus-empty crash rollover ratio match that statement?
Show answer
Answer: B. Slow for the ramp; the cited crash rollover ratio for loaded versus empty rigs is ten to one
This answer reproduces the selected NY manual Section 6.1.1 teaching statement about loaded versus empty rigs in crashes. It is not a universal quantitative risk model. The manual edition and page number have not been independently verified in this offline revision.
3. Use the selected NY CDL Manual Section 6.1.2 crack-the-whip chart’s teaching wording “times as easily,” with a five-axle tractor-trailer as the baseline. How does its 3.5 value describe the last trailer of triples? Treat this as the chart’s comparison, not a measured crash-probability ratio.
Show answer
Answer: A. The last trailer can roll 3.5 times as easily as the five-axle tractor-trailer baseline
The answer follows the selected NY manual Section 6.1.2 chart’s “3.5 times as easily” teaching comparison for the last trailer of triples against a five-axle tractor-trailer. Rearward amplification describes amplified lateral response; do not interpret this wording as a general statistical crash probability. Chart number, edition, and page remain unverified offline.
4. A 60-foot combination is traveling at 45 mph in traffic. What following-distance practice does the combination-vehicles section describe?
Show answer
Answer: C. Allow seven seconds: one per ten feet plus one above 40 mph
The manual says to follow far enough behind other vehicles: at least 1 second for each 10 feet of your vehicle length, plus another second if going over 40 mph. It also says to look far enough down the road to avoid being surprised and having to make a sudden lane change. The 60-foot length and 45 mph speed in the stem are only a scenario setup so the driver can apply that stated rule; the manual itself does not quote a ready-made 60-foot example.
5. A lightly loaded combination needs to stop for slowed traffic ahead. Why does the manual tell the driver to brake with extra care?
Show answer
Answer: D. Stiff springs and strong brakes reduce traction and make wheel lockup easier
The manual says large combination vehicles take longer to stop when they are empty than when they are fully loaded. When lightly loaded, the very stiff suspension springs and strong brakes give poor traction and make it very easy to lock up the wheels. The trailer can swing out and strike other vehicles, and the tractor can jackknife very quickly. Allow lots of following distance and brake early; do not be caught by surprise and have to make a panic stop.
6. A driver is repositioning a tractor with no semitrailer attached (bobtail). What stopping characteristic does the manual report?
Show answer
Answer: B. A bobtail can stop less smoothly and take longer than a fully loaded combination
The manual warns drivers to be very careful about driving bobtail tractors (tractors without semitrailers). Tests have shown that bobtails can be very hard to stop smoothly. It takes them longer to stop than a tractor-semitrailer loaded to maximum gross weight.
7. A driver pulling a lowboy (and later a car carrier) is approaching a railroad-highway crossing that is noticeably humped in the middle. What hang-up problem should the driver anticipate?
Show answer
Answer: C. The trailer's low underside may hang up on the raised profile of the crossing
The manual says railroad-highway crossings can cause problems, particularly when pulling trailers with low underneath clearance. These trailers can get stuck on raised crossings, including low-slung units such as a lowboy, car carrier, moving van, or possum-belly livestock trailer, and a single-axle tractor pulling a long trailer with its landing gear set to accommodate a tandem-axle tractor. This item uses an original approach-to-the-crossing scenario; it does not copy the manual’s end-of-section review wording.
8. A moving van is immobilized on a raised railroad crossing. The driver must evacuate everyone immediately to a safe place away from the tracks. Which sequence then best supports urgent railway and emergency notification, without delaying evacuation to find a sign or make a call?
Show answer
Answer: C. Evacuate first; use posted railway contacts and call 911 with crossing location and DOT ID
Evacuate everyone to safety first. Then use posted railway emergency notification information and contact 911 with the crossing location and DOT identifier if available. Searching for signage or making calls must not delay evacuation. This does not prescribe a universal regional order between railway and emergency calls.
9. After a hard brake application, the driver sees in the mirrors that a lightly loaded trailer has started to swing toward a jackknife. What is the correct response?
Show answer
Answer: D. Release brakes to regain traction; leave the trailer hand brake released
When trailer wheels lock up, the trailer tends to swing around (a trailer jackknife), which is more likely when the trailer is empty or lightly loaded. The earliest and best way to recognize the skid is in the mirrors. The procedure is to stop using the brake and release the brakes to get traction back. Do not use the trailer hand brake to “straighten out the rig”; the brakes on the trailer wheels caused the skid in the first place. Once the trailer wheels grip the road again, the trailer will start to follow the tractor and straighten out.
10. A long combination must turn right at a tight urban corner where other drivers may try to sneak by on the right. How should the driver manage offtracking?
Show answer
Answer: B. Keep the rear near the curb and widen the path as you complete the turn
The rear wheels follow a different path than the front wheels (offtracking or “cheating”). Longer vehicles offtrack more, and if there is more than one trailer, the rear wheels of the last trailer offtrack the most. Steer the front end wide enough around a corner so the rear end does not run over the curb or pedestrians, but keep the rear close to the curb to stop other drivers from passing on the right. If you cannot complete the turn without entering another traffic lane, turn wide as you complete the turn. That is better than swinging wide to the left before starting the turn.
11. A driver is turning a combination that has more than one trailer. Which axle path should the driver expect?
Show answer
Answer: A. The last trailer's rear wheels offtrack more than the wheels of earlier units
The manual states that the rear wheels of the powered unit (truck or tractor) will offtrack some, and the rear wheels of the trailer will offtrack even more. If there is more than one trailer, the rear wheels of the last trailer will offtrack the most. Longer vehicles will offtrack more.
12. A driver must back a trailer into a dock. Which practice matches the combination-vehicles section?
Show answer
Answer: B. Favor straight backing; curve to the driver side and steer the wheel top toward drift
When backing a trailer, you turn the steering wheel in the opposite direction from the way you would when backing a car, straight truck, or bus; once the trailer starts to turn, you must turn the wheel the other way to follow the trailer. Try to position the vehicle so you can back in a straight line. If you must back on a curved path, back to the driver’s side so you can see. Back slowly, and as soon as you see the trailer getting off the proper path, correct it by turning the top of the steering wheel in the direction of the drift. Make pull-ups to reposition as needed. Look at the path first, use both outside mirrors, and get out and reinspect if you are unsure.
13. A driver wants to hold a combination on a grade by leaving the trailer hand valve (trolley valve or Johnson bar) applied and walking away. Why is that the wrong parking method?
Show answer
Answer: A. Leaking air can release non-spring trailer brakes; use parking brakes and chock non-spring trailers
The trailer hand valve should be used only to test the trailer brakes. Do not use it in driving because of the danger of making the trailer skid; the foot brake sends air to all of the brakes, with much less danger of a skid or jackknife. Never use the hand valve for parking because all the air might leak out, unlocking the brakes in trailers that don’t have spring brakes. Always use the parking brakes when parking. If the trailer does not have spring brakes, use wheel chocks to keep the trailer from moving.
14. A trailer air hose ruptures and pressure in the combination starts to fall. What does the tractor protection valve do when it closes?
Show answer
Answer: C. It retains tractor air and vents the emergency line, applying trailer emergency brakes
The tractor protection valve keeps air in the tractor or truck brake system should the trailer break away or develop a bad leak. It is controlled by the trailer air supply control in the cab. The valve will close automatically if air pressure is low (in the range of 20 to 45 psi). When it closes, it stops any air from going out of the tractor and lets the air out of the trailer emergency line, which causes the trailer emergency brakes to come on, with possible loss of control.
15. On a newer tractor, the trailer air supply control is a red eight-sided knob. How is that control used?
Show answer
Answer: D. Push to supply air; pull to shut supply and apply trailer emergency brakes
The trailer air supply control on newer vehicles is a red eight-sided knob used to control the tractor protection valve. You push it in to supply the trailer with air, and pull it out to shut the air off and put on the trailer emergency brakes. The valve will pop out (closing the tractor protection valve) when air pressure drops into the range of 20 to 45 psi. On older vehicles, the “normal” position is used for pulling a trailer, and the “emergency” position is used to shut the air off and put on the trailer emergency brakes.
16. A driver is tracing the two air lines between a tractor and a semitrailer. What jobs does the emergency (supply) line perform?
Show answer
Answer: C. It supplies trailer reservoirs and controls the combination's trailer emergency brakes
Every combination vehicle has two air lines. The service line (also called the control or signal line) carries air controlled by the foot brake or the trailer hand brake; its pressure changes with how hard you press, and it is connected to relay valves so trailer brakes can be applied more quickly. The emergency line (also called the supply line) supplies air to the trailer air tanks and controls the emergency brakes. Loss of air pressure in the emergency line causes the trailer emergency brakes to come on and also causes the tractor protection valve to close (the air supply knob will pop out). Emergency lines are often color-coded red to keep them from being mixed up with the blue service line.
17. After hooking a trailer, the driver pushes in the trailer air supply control, but the trailer spring brakes will not release. The glad-hand colors also look mixed up. What should the driver suspect, and how are glad hands correctly joined?
Show answer
Answer: D. Suspect crossed air lines; match couplers, press seals together at 90 degrees, and twist to lock
Glad hands connect the service and emergency air lines. Clean the couplers and rubber seals before connecting. Press the two seals together with the couplers at a 90-degree angle, then turn the glad hand attached to the hose to join and lock them. Couple the proper glad hands together (blue for service, red for emergency, or metal tags). If you cross the air lines, supply air is sent to the service line instead of charging the trailer air tanks, and air will not be available to release the trailer spring brakes. If the spring brakes don’t release when you push the trailer air supply control, check the air line connections. On older trailers without spring brakes, crossed lines could let you drive away without trailer brakes. Always test the trailer brakes before driving.
18. According to the daily inspection instructions in the selected NY CDL Manual Section 6, which line charges trailer or dolly air tanks and how often does that manual call for manual draining? Use this manual’s training rule rather than a universal maintenance interval for all equipment.
Show answer
Answer: C. The supply line fills each tank; manually drain tanks daily, including tanks with automatic drains
For this question, the selected NY manual’s daily draining rule applies, including tanks with automatic drains. The supply line charges the tanks. Equipment-specific maintenance must also follow manufacturer instructions; the manual edition and page remain unverified offline.
19. A driver has coupled a first trailer that will tow a second trailer, plus a last trailer that will not tow another unit. How should the shut-off valves (cut-out cocks) be set?
Show answer
Answer: A. Open valves between units and close valves at the rear of the last trailer
Shut-off valves (also called cut-out cocks) are used in the service and supply air lines at the back of trailers used to tow other trailers. They permit closing the air lines off when another trailer is not being towed. You must check that all shut-off valves are in the open position except the ones at the back of the last trailer, which must be closed.
20. A driver must park a trailer that has no spring brakes (for example, some older trailers or converter dollies). Why are wheel chocks required?
Show answer
Answer: A. Reservoir air can leak away and release this trailer’s air-applied emergency brakes
Converter dollies and trailers built before 1975 are not required to have spring brakes. Those that do not have spring brakes have emergency brakes that work from the air stored in the trailer air tank and come on whenever air pressure in the emergency line is lost. These trailers have no parking brake. The emergency brakes come on when the air supply knob is pulled out or the trailer is disconnected, but they will hold only as long as there is air pressure in the trailer air tank. Eventually the air will leak away and then there will be no brakes. Therefore it is very important for safety that you use wheel chocks when you park trailers without spring brakes.
21. During a walk-around of a coupled trailer, where should the driver look for the trailer’s ABS malfunction lamp?
Show answer
Answer: C. A yellow lamp on the trailer's left front or left rear corner
The manual states that trailers will have yellow ABS malfunction lamps on the left side, either on the front or rear corner. Dollies are also described as having a lamp on the left side. This item asks only for the lamp location used in a walk-around, not for manufacture-date applicability rules covered in Set 1.
22. A driver asks whether ABS on a tractor-trailer will make every stop shorter and stronger than the ordinary service brakes. What does the manual say ABS does and does not do?
Show answer
Answer: A. ABS supplements normal brakes near wheel lockup; stopping distance may remain unchanged
ABS is an addition to your normal brakes. It does not decrease or increase your normal braking capability. ABS only activates when wheels are about to lock up. ABS does not necessarily shorten your stopping distance, but it does help you keep the vehicle under control during hard braking. The computer senses impending lockup, reduces the braking pressure to a safe level, and you maintain control. ABS won’t allow you to drive faster, follow more closely, or drive less carefully.
23. A combination has working ABS on the trailer only. During a hard stop, the trailer stays in line, but the tractor begins to jackknife. What should the driver do?
Show answer
Answer: D. Ease braking when safe; trailer ABS reduces swing but cannot stop tractor jackknife
Having ABS on only the trailer, or even on only one axle, still gives you more control over the vehicle during braking. When only the trailer has ABS, the trailer is less likely to swing out, but if you lose steering control or start a tractor jackknife, let up on the brakes (if you can safely do so) until you gain control.
24. A driver is assigned a tractor-trailer that has ABS on both units. How should that driver brake, according to the combination-vehicles section?
Show answer
Answer: D. Brake normally with the force needed for a safe stop, regardless of ABS equipment placement
When you drive a tractor-trailer combination with ABS, you should brake as you always have: use only the braking force necessary to stop safely and stay in control; brake the same way, regardless of whether you have ABS on the tractor, the trailer, or both; and as you slow down, monitor your tractor and trailer and back off the brakes (if it is safe to do so) to stay in control.
25. A trailer’s left-side yellow ABS malfunction lamp stays on after departure. Ordinary service brakes have been checked and remain functional, with no other brake warning or defect. Which response addresses the ABS fault under the manual’s guidance?
Show answer
Answer: A. Use regular brakes cautiously and arrange prompt ABS service while maintaining safe margins
A persistent ABS lamp calls for prompt service. With ordinary brakes confirmed functional, use regular braking cautiously and retain normal safe speed and following margins. The answer is not an unconditional legal authorization to continue every trip.
26. Before coupling a trailer, inspect a conventional fifth wheel whose manufacturer requires plate lubrication. Its plate is dry, its front edge is tilted down, and its jaws are closed. Which preparation and lubrication rationale match the manual? Follow manufacturer lubrication requirements.
Show answer
Answer: A. Lubricate as required, tilt rear down, and open jaws; a dry plate can impair steering
For the conventional lubricated fifth wheel described, grease as required by its manufacturer, tilt the rear down, and open the jaws. Insufficient lubrication can cause steering problems. Low-friction liner designs may have different requirements.
27. In a crowded yard, a driver starts to back under a trailer from an angle to save a pull-up, and no one has chocked the trailer wheels. What does the manual require instead?
Show answer
Answer: D. Align straight; chock or set spring brakes; angled backing risks landing-gear damage
Step 2 says to make sure the area is clear, be sure trailer wheels are chocked or spring brakes are on, and check that cargo is secured against movement due to the tractor being coupled. Step 3 says to put the tractor directly in front of the trailer. Never back under the trailer at an angle because you might push the trailer sideways and break the landing gear. Check position using outside mirrors, looking down both sides of the trailer. Back slowly until the fifth wheel just touches the trailer, and don’t hit the trailer.
28. After the fifth wheel just touches the trailer, the driver checks height and sees that backing under will not lift the trailer at all. Why must that height be corrected before the couple?
Show answer
Answer: B. Set trailer slightly low for tractor lift; excessive or insufficient height risks miscoupling or damage
Step 6 says the trailer should be low enough that it is raised slightly by the tractor when the tractor is backed under it. Raise or lower the trailer as needed. If the trailer is too low, the tractor may strike and damage the trailer nose; if the trailer is too high, it may not couple correctly. Also check that the kingpin and fifth wheel are aligned. This is an original height-check scenario, not a copy of the manual’s review-question wording.
29. The combination is secured against movement with the tractor parking brake and trailer wheel chocks. Glad hands are connected and the trailer air supply knob is pushed in. Which stationary procedure checks for crossed air lines before continuing the coupling?
Show answer
Answer: A. At normal pressure, stop engine, cycle trailer brakes, listen for action/air escape, and watch gauge
With the combination securely fixed against movement, reach normal pressure, shut off the engine, and apply and release the trailer brakes. Listen for brake action and escaping air and observe the gauge. Leakage and low-air tests serve different inspection purposes.
30. Trailer brakes have just been confirmed to be working. What should the driver do next to lock the couple and test it?
Show answer
Answer: B. Pull trailer supply out, back slowly to lock, raise gear slightly, and tug against trailer brakes
Step 9 is to lock trailer brakes by pulling out the air supply knob or moving the tractor protection valve control from “normal” to “emergency.” Step 10 is to back under in the lowest reverse gear, slowly, to avoid hitting the kingpin too hard, and stop when the kingpin is locked into the fifth wheel. Step 11 is to raise the trailer landing gear slightly off the ground and pull the tractor gently forward while the trailer brakes are still locked, to check that the trailer is locked onto the tractor.
31. After the tug test, a driver looks at the fifth wheel with a flashlight and sees a visible gap between the upper and lower halves. What does that finding mean?
Show answer
Answer: C. The kingpin may be perched on closed jaws, indicating an insecure coupling that could separate
Step 13 says to inspect the coupling (use a flashlight if necessary). Make sure there is no space between the upper and lower fifth wheel. If there is space, something is wrong (the kingpin may be on top of the closed fifth wheel jaws, and the trailer would come loose very easily). If the coupling isn’t right, don’t drive the coupled unit; get it fixed. This scenario does not copy the manual’s review-question wording.
32. After a tug test, the driver secures the combination against movement, selects neutral, sets parking brakes, shuts off the engine, and takes the key. Before proceeding under the trailer with a flashlight, the vehicle is safely fixed in place. What must the fifth-wheel inspection confirm?
Show answer
Answer: A. Confirm jaws around kingpin shank, locking lever locked, and safety latch over the lever
Secure the vehicle before going underneath. The jaws must surround the kingpin shank, not its head; the locking lever must be locked and its safety latch engaged.
33. After a successful couple, a driver raises the landing gear only until it clears the pavement by a few inches and leaves the crank handle loose. Why is that unsafe, and how should the gear be raised?
Show answer
Answer: B. Use low then high gear, raise fully, and secure the crank to prevent road-obstacle contact
Step 15 says to use low gear range (if so equipped) to begin raising the landing gear; once it is free of weight, switch to the high gear range. Raise the landing gear all the way up. Never drive with landing gear only part way up, as it may catch on railroad tracks or other things. After raising it, secure the crank handle safely. When the full weight of the trailer is resting on the tractor, check for enough clearance between the rear of the tractor frame and the landing gear (the tractor must not hit the landing gear in a sharp turn) and between the top of the tractor tires and the nose of the trailer. Then remove and store the wheel chocks. Also connect the electrical cord, fasten the safety catch, and make sure air and electrical lines will not hit moving parts (Step 14).
34. A driver is uncoupling a loaded trailer on firm ground. After shutting off the trailer air supply and easing pressure on the locking jaws, what should be done with chocks and the landing gear?
Show answer
Answer: D. Chock if spring brakes are absent/uncertain; lower gear, add low-gear turns, and avoid lifting clear
Uncoupling Step 1: make sure the surface can support the trailer and have the tractor lined up (pulling out at an angle can damage landing gear). Step 2: shut off trailer air supply to lock trailer brakes, ease pressure on the fifth-wheel locking jaws by backing up gently, and put the parking brakes on while the tractor is pushing against the kingpin. Step 3: chock the trailer wheels if the trailer doesn’t have spring brakes or if you’re not sure (air could leak out of the trailer air tank, releasing its emergency brakes). Step 4: if the trailer is empty, lower the landing gear until it makes firm contact with the ground; if it is loaded, after firm contact, turn the crank in low gear a few extra turns to lift some weight off the tractor. Do not lift the trailer off the fifth wheel. That makes it easier to unlatch the fifth wheel and easier to couple next time.
35. The fifth-wheel release handle is in the open position, and the air and electrical lines have been disconnected. How far should the driver first pull the tractor, and why?
Show answer
Answer: B. Pull until the fifth wheel clears, then stop with tractor frame beneath as a support safeguard
After disconnecting air lines (glad hands to dummy couplers or coupled together) and hanging the electrical cable with the plug down to prevent moisture from entering it, unlock the fifth wheel, keeping legs and feet clear of the rear tractor wheels. Step 7: pull the tractor forward until the fifth wheel comes out from under the trailer, and stop with the tractor frame under the trailer (this prevents the trailer from falling to the ground if the landing gear should collapse or sink). Then secure the tractor, inspect that the ground is supporting the trailer and the landing gear is not damaged, and only then drive the tractor forward until it clears.
36. On a walk-around of an already coupled combination, which fifth-wheel finding is acceptable?
Show answer
Answer: C. Plates flush, jaws around the kingpin shank, release arm seated, and safety latch engaged
In addition to the Section 2 walk-around, check the lower fifth wheel: securely mounted to the frame, no missing or damaged parts, enough grease, no visible space between the upper and lower fifth wheel, locking jaws around the shank—not the head—of the kingpin, and the release arm properly seated with the safety latch/lock engaged. Check the upper fifth wheel: glide plate securely mounted to the trailer frame, and the kingpin not damaged.
37. During the walk-around, the driver reaches the sliding fifth wheel and the landing gear. Which condition is acceptable for travel?
Show answer
Answer: C. Slider undamaged, pins locked, landing gear fully raised, and crank secured
For a sliding fifth wheel, check that the slide is not damaged or missing parts, that it is properly greased, that all locking pins are present and locked in place, that an air-powered slider has no air leaks, and that the fifth wheel is not so far forward that the tractor frame will hit the landing gear, or the cab hit the trailer, during turns. Landing gear should be fully raised, with no missing parts, not bent or otherwise damaged, the crank handle in place and secured, and no air or hydraulic leaks if it is power operated.
38. On the combination walk-around, what should the driver confirm about the air and electrical lines to the trailer?
Show answer
Answer: D. Secure electrical plug, sealed glad hands, and sufficient protected slack for turns
The walk-around should confirm that the electrical cord is firmly plugged in and secured; that air lines are properly connected to glad hands, with no air leaks, and properly secured with enough slack for turns; and that all lines are free from damage. This is the Section 6.5.1 operational inspection point for combination vehicles, not a federal hose-installation rule item from Set 1.
39. A charged triple is secured with the tractor parking brake and wheel chocks before the driver leaves the cab. The red trailer supply knob is pushed in and the trailer hand brake is applied for the test. At the rear of the last trailer, which check confirms air reaches both lines?
Show answer
Answer: B. Open and close each rear valve in turn and hear air from both charged lines
With the tractor parking brake and chocks securing the combination, trailer supply pushed in and hand brake applied, open the last trailer emergency-line rear shut-off, listen for escaping air, and close it. Repeat with the service-line valve and close it. These shut-offs remain closed for travel.
40. After confirming the system is charged, the driver needs to test the trailer’s emergency brakes and then its service brakes. Which procedure matches the manual?
Show answer
Answer: B. Test emergency brakes with supply pulled out and a gentle tug; test service brakes with hand valve at low speed, using the foot pedal on road
To test trailer emergency brakes, charge the trailer air brake system and check that the trailer rolls freely. Then stop and pull out the trailer air supply control (also called the tractor protection valve control or trailer emergency valve), or place it in the “emergency” position. Pull gently on the trailer with the tractor to check that the trailer emergency brakes are on. To test trailer service brakes, check for normal air pressure, release the parking brakes, move the vehicle forward slowly, and apply the trailer brakes with the hand control (trolley valve), if so equipped. You should feel the brakes come on, telling you the trailer brakes are connected and working. The trailer brakes should be tested with the hand valve but controlled in normal operation with the foot pedal, which applies air to the service brakes at all wheels. (The tractor protection valve is tested separately by charging the system, shutting the engine off, and fanning the pedal until the air-supply control pops out, usually in the 20 to 45 psi range.)
Frequently asked questions
Is this an official exam?
No. These are original, unofficial practice questions written by PocketLearn. They are not released exam items. Unofficial original practice. Check current official exam materials. Not a complete exam review.
How many questions are there?
40 multiple-choice questions. Each question has an explanation.
Is it free?
Yes. You can open the practice set without an account; signing in lets you save progress and review mistakes.
Can I use it on my phone?
It opens in a mobile browser. A laptop or tablet is easier for longer sets.
More free practice tests
- CDL Air Brakes practice test
- CDL General Knowledge practice test
- CDL Combination Vehicles practice test
- CompTIA Security+ SY0-701 practice test
- NCLEX Pharmacology Fundamentals practice test
- NCLEX Pediatrics practice test
- Florida Real Estate Course I Unit 1 practice test
- Life and Health Insurance practice test
- FAA Part 107 Regulations practice test
- NCLEX Respiratory practice test
- CDL Pre-Trip Inspection practice test
- California Real Estate Salesperson Set 2 practice test
- NCLEX Pharmacology: Legal and Ethical Medication Safety practice test
- NCLEX Pharmacology: Antimicrobial Medications practice test
- Florida Real Estate Unit 3 Practice (Unofficial) practice test
- Florida Real Estate Unit 4: Relationships, Duties and Disclosure practice test
- CDL Air Brakes Practice — Set 3 practice test
- New York CDL HazMat Practice — Set 2 practice test
- CompTIA A+ Core 2 Practice Test Set 3 (Unofficial) practice test
- EPA Section 608 Core Practice Test (Unofficial) practice test
- Journeyman Electrician Basics Practice Test (Unofficial) practice test
- 2025 U.S. civics practice test
- Technician Class (ham radio) practice test